CAD/CAM Machine (RPT)
CAD Software
Engraving Machine
Casting Machine
Mold Rubber
Tools / Files
Alloys
Plating Solution
Polishing Compounds
Weighing Scale

Content on this page requires a newer version of Adobe Flash Player.

Get Adobe Flash player
4X GOLD SILICONE MOLD RUBBER
4X Silicone Mold Rubber are soft with extremely high tear strength and is intended to be used for very intricate designs. This rubber is designed for hand cutting method. If you wish to use powder separation method, use more powder than you would with other stiffer, lower strength products. If you do not use extra powder, you will not obtain good separation. Perfect for platinum or any other applications due to very high pattern finish.

We recommend that you use stainless steel mold plates as this product tends to adhere more strongly to aluminum plates.
 
MAKING THE MOLD:
Using scissors, cut enough rubber to fill the mold frame to about 1/2 to 2/3 full. Work in with your fingers or a blunt tool.
Push model into rubber to proper position and then cover over with additional rubber. Work into place, being sure to over pack slightly.
Place mold frame in vulcanizer pre-heated to between 330°F and 350°F
(165°C and 177°C). Vulcanize 15 minutes per 1/4" (6.35mm) of thickness. A 3/4" (19mm) frame requires 45 minutes.
 
Release agent is not required.

Shrink rate is 2.8%
Maximum short term temperature exposure: 500°F.
QUICK-CURE™
 
SILICONE MOLD RUBBER
 
QUICK-CURE Silicone Mold Rubber is an economical, medium to firm rubber with extremely high tear strength and very rapid cure. It is intended to be used for all applications. Detail replication is excellent. Perfect for platinum applications due to very high pattern finish.

You can have a mold ready to inject in 30 minutes if you pre-heat your vulcanizer.
 
  • Pre-heat your vulcanizer to 350°F (177°C)
  • Using scissors, cut enough rubber to fill the mold frame to about 1/2 to 2/3 full.
  • Push model into rubber to proper position and then cover over with additional rubber. Work into place, being sure to over pack slightly.
  • Place mold frame in vulcanizer, pre-heated to 350°F (177°C).
  • Vulcanize 7 minutes per 1/4" (6.35mm) of thickness. A 1/2" frame requires 14 minutes.
  • Rapid cool in water and cut.
 
Release agent is not required.
Shrink rate is 1.8% (rubber only)
4X BLUE™ SILICONE MOLD RUBBER

GENERAL PURPOSE FLAT WORK
ABOUT 4X BLUE™
 
4X Blue Silicone Mold Rubber is an economical, very firm rubber with moderately high tear strength and is intended to be used for flat pieces. This rubber is designed for the powder separation method. We recommend that you use stainless steel mold plates as this product tends to adhere more strongly to aluminum plates.
 
MAKING THE MOLD:
 
  • Using scissors, cut enough rubber to fill the mold frame to about 1/2 to 2/3 full. Work in with your fingers or a blunt tool.
  • Push model into rubber to proper position and then cover over with additional rubber. Work into place, being sure to over pack slightly.
  • Place mold frame in vulcanizer pre-heated to between 330°F and 350°F (165°C and 167°C). Vulcanize 15 minutes per 1/4" (6,35mm) of thickness. A 3/4" (19mm) frame requires 45 minutes.
 
Release agent is not required.
 
Shrink rate is 1.6% (rubber only)
Maximum long term temperature exposures: 500°F.
Maximum short term temperature exposure: 900°F.
 
  For More Details : www.zerodproducts.com
Home About Us Product Enquiry Contact Us
Copyright © 2010 Sarto Electro. All Rights Reserved.